sveiki, yra a6 c5 2,5tdi 132kw AKE 2000m. nusipirkau variklio kompa ir nzn kaip ji priristi. bandziau kaip wiki.ross'e raso , bet nesigauna.

dariau taip, nuskaiciau 4 skaiciu pin koda (0339) su vag taxo, tada per vag'a uzeini y skydeli, spaudi login suvedi 00339  spaudi do it, tada jis greitas ismeta y skydeli, poto wiki raso kad vel turi spaust login ir turi but xxxxx taip, bet pas mane tie patys 00000. gal kazka ne taip darau ?

dar bandziau uzeit y skydeli ir variklio kompa, adaptation tada 00 read ir save, bet irgi be jokiu rezultatu.

uzvedi ir uzgesta. variklio kompe raso kad varikli blokuoja imobilaizeris.

dariau taip, nuskaiciau 4 skaiciu pin koda (0339) su vag taxo

O loginas cia  kieno: skyduko ar to naujo naudoto ECU?  Loginas turi buti skyduko ir visus veiksmus daryti per skyduka.Man,kaip nekeista,irgi viskas pavykdavo tik ivedus logina,net ir immo2 sistemai

viska isbandziau. pin skyduko. ir meistriuka kazkoki pasikvieciau kuris atlieka diagnostikas, bet puse dienos jis ten prasikniso ir be rezultatu. tai dabar yra dar vienas dedukas kuriam bus nunestas kompas ir skydelis, paziuresim, tas turi padaryt. o 132kw ejo jau ir 2000m. ir netgi su mex greiciu deze, kuri buvo ideta y mano auto sugedus automatui.

dariau pagal sita. kai uzeini y skydeli tai rodo ta extra numeni, pries ji yra tik daug rusisku "ja"raidziu. o immo II neradau kaip risti. bet jau kompas atiduotas meistrui,tai laukiu kol padarys.


Immobilizer I ECU Swapping
This procedure details how to swap engine control modules on VW/Audi/Seat/Skoda vehicles with Immobilizer I.
Contents [hide]
1 Determining IMMO-ID
2 ECU Swapping
Determining IMMO-ID

[Select]
[25 - Immobilizer]
or in vehicles with Immobilizer included in Instrument Cluster
[17 - Instruments]
Look at the first "Extra" field. You should see something like: Immo-ID VWZ7Z0W0648696.
[Close Controller, Go Back - 06]

ECU Swapping

Prerequisites:
Battery voltage at least 12.0 V.

[Select]
[25 - Immobilizer]
or in vehicles with Immobilizer included in Instrument Cluster
[17 - Instruments]
[Login - 11]
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
4-digit PIN
Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
7-digit PIN
[Use 7-digit PIN/SKC]
Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
[OK]
VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Do it!]
[Adaptation - 10]
Enter 000 in "Channel Number".
[Adaptation - 10]
Channel 000
[Read]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
Switch OFF the ignition and after 5 seconds switch it ON again.
Make sure NOT to start the car within the next 2 minutes. After that, try starting the engine.